PS DOORS Edgehalt Adjustable Safety Gates | Raptor Supplies Singapore
Onboard Raptor as a vendor

PS DOORS Edgehalt Adjustable Safety Gates

PS Doors EdgeHalt adjustable safety gates protect workers from the dangerous falls due to an elevated guardrail opening in manufacturing, automobile, construction & aviation ...Read More

Filter
PS DOORS ASG-1836-PCYA
PS DOORS ASG-1836-ZINCB
StyleModelFinishMaterialOpening WidthColorPrice (inc. GST)
A
ASG-1836-PCY		Powder CoatedMild Steel18" to 36"Yellow SGD 640.99
B
ASG-1836-ZINC		Zinc PlatedMild Steel18" to 36"Gray SGD 752.10

Working Mechanism

    • Installation on standard railings:
      1. Loosely fix the safety gate to the railing using U-bolts without tightening them.
      2. Align the top of the gate to the top of the railing.
      3. Adjust the railing / mounting bracket to be 90 degrees to the safety gate's opening and tighten the U-bolts.
      4. Select two out of the three carriage bolt holes at the joining point of the hinge plate & hoop / gate arms for adjusting the hoop / gate arm to the required opening width.
      5. The gate's stop plate should overlap & contact the adjacent vertical railing column.
      6. Check for proper alignment by fully operating the gates.
      7. Fully tighten the U-bolts with 20 ft-lb torque and use adequate attachments like protective thread caps.
    • Installation on angle railings or flat bar railing / wall surface:
      1. Fix the railing bracket of the safety gate flush to the inside of the angled railing or on the flat bar / flat wall.
      2. Align the top of the gate to the top of the railing.
      3. Drill holes into the railing and insert mounting bolts through the railing brackets. Adjust the top of hoop / gate arm to 42 inch above the walking surface if no railing found.
      4. The rest of the steps for adjusting the gate arm to the appropriate opening width are the same as the installation steps on standard railings.
    • Operating safety gate while ascending a ladder or entering the elevated platform:
      1. Climb the ladder till the user reaches the gate.
      2. Securely hold the railing or ladder and step through the gate onto the elevated platform.
    • Operating safety gate while descending a ladder or exiting the elevated platform:
      1. Open the safety gate while obtaining a secure grip on the ladder railing.
      2. Then, users can manoeuvre themselves into the appropriate ladder descending position and start descending until ground level.

Features

  • These gates can swing in both left and right directions by simply inverting them.
  • They offer a versatile adjustable design to fit openings ranging from 18 to 36 inches.
  • They are easily installable without any sawing or cutting, using a tape measure and deep-well socket & ratchet, wrench set / torque wrench or an impact drill with a nut driver.
  • The gate is made of mild steel with a safety yellow powder coating or zinc-coated finish for durability, visibility & structural strength.
  • These self-closing gates use springs that can withstand over 1 million cycles for round the clock safety / protection.
  • They come in a ready to install kit containing pre-assembled parts (hinge plate assembly, hoop, carriage bolts, flat washers & nylock nuts), a hardware bag and an optional support block kit.

Compatible Accessories

  • Lock-Out Kit: This kit prevents unauthorised entry into restricted areas, mezzanines or elevated platforms by locking the gate.
  • Standoff Mounting System: This system mounts directly to existing railing & adjustable safety gates for increasing the platform space of a mezzanine edge and providing a grab spot for workers using ladder / rails. The system helps in easy & safe movement of personnel from the ladder onto the elevated platform.
  • Ladder Accessories: Raptor Supplies offers PS Doors ladder accessories & replacement parts like hinge plate assemblies for replacing old, worn-out or faulty parts of the safety gates.

Standards and Approvals

  • CE
  • OSHA
  • ANSI
  • CSA

Frequently Asked Questions

How can users determine the size of the safety gate required?

Users can simply measure the clear opening from one handrail / railing to another, then adjust these safety gates according to desired opening size.

How to select between zinc-coated or safety yellow powder-coated safety gates?

Galvanised or zinc coating protects against corrosion and offers durability in outdoor conditions or harsh environments. Safety yellow powder coating is generally used in indoor applications for high visibility.

What are the points to consider before installing or operating the PS Doors EdgeHalt adjustable safety gates?

  • Users should ensure that the gate opening / travel area is free from all obstructions during operation.
  • They should adhere to OSHA & ANSI safety regulations and company safety policies when installing or operating the safety gates.
  • Before installing, users should get a structural analysis of the mounting surface, ensuring that it can support all loading & operate safely.
  • All installation personnel should wear suitable fall protection equipment & follow safety precautions while installing the gates.
  • These safety gates should be properly maintained to ensure failure-free, efficient performance.

What are some troubleshooting tips for these PS Doors EdgeHalt adjustable safety gates?

  • The gate components, fasteners and mechanical connections should be inspected for damage & misalignment. They should be then adjusted, repaired or replaced if required, to meet desired design tolerance.
  • The gates can be adjusted as needed to ensure proper alignment.
  • The finish on the units should be periodically inspected, cleaned & re-applied to protect their structural integrity.
  • These safety gates should undergo inspection and maintenance checks annually (minimum) for safe & efficient operation.

We are here to help!

Looking for a part not listed here?

Chat with us now

Popular Search Queries

Explore More